Market data in this article is as of June 2026.
At a glance
In June 2026, national dry-van spot pricing moved above contract pricing, according to DAT.
The demand picture requires care. BTS's freight index is a multimodal measure, and trucking volumes were rising in its June release even though other modes were declining.
For buyers, the rate gap can signal exposure on important lanes. For fleet operators, it reinforces the need to understand which vehicles and drivers are actually available.
A transportation contract can provide pricing stability while the market around it changes. Spot prices respond quickly to immediate conditions; negotiated rates usually adjust less frequently. When the gap widens, transportation leaders have a reason to revisit the assumptions behind their plans.
The practical question extends beyond what the next load will cost. Can the network still cover its commitments, and how much of its existing capacity is ready to work?
A negotiated rate is not, by itself, a guarantee that a carrier will accept every load. Likewise, a national spot premium does not establish that every lane is tight. Compare similar lanes, equipment, service requirements, and fuel treatment before drawing conclusions about your own network.
Capacity on paper is not capacity ready to move
Registered carrier counts cannot tell a transportation team how many suitable trucks and qualified drivers are available for a particular movement. A business may remain registered while operating fewer vehicles or serving fewer lanes.
The same distinction applies inside a fleet. A vehicle awaiting repair cannot cover its planned run. A driver on the roster may be unavailable for the required shift. An inspection issue discovered just before departure may force a reassignment when alternatives are already limited.
These are practical reasons to track vehicle readiness and driver coverage together. When replacement capacity becomes more expensive, late discovery of an internal gap can become more costly too.
What the June 2026 data shows
DAT reported a national average dry-van spot rate of $3.00 per mile in June, compared with a contract rate of $2.89, both including fuel. This was the first spot-over-contract crossover since February 2022. Van volumes rose 11% from May but were roughly flat year over year. Pricing therefore strengthened without comparable annual volume growth. (DAT, July 9, 2026)
Contract prices were also adjusting. Van contract linehaul rates rose seven cents to $2.26 per mile, while spot linehaul rates rose 21 cents to $2.37. Lower fuel surcharges brought the all-in contract average down. The shift was faster spot-price growth, not an absence of movement in contract pricing.
The Bureau of Transportation Statistics (BTS) tracks a Freight Transportation Services Index across several modes. In its June release, trucking and rail intermodal volumes increased while several other modes declined, so the overall index does not establish falling trucking demand. BTS revised the June freight index upward in its July release, so check its latest data before relying on any single month. (BTS)
Taken together, these figures support examining capacity pressure, while leaving room for seasonal and lane-specific demand changes. They do not establish that every network faces the same conditions.
For transportation buyers: identify where coverage is exposed
Use the national rate gap as a prompt for a lane-level review. Prioritize movements where spot alternatives are becoming more expensive, contracted loads are being declined more often, or service performance is deteriorating.
Tender rejection rates add context: they show how often carriers decline offered loads. A rising rejection rate can indicate pressure on contracted coverage, but it needs to be read alongside shipment timing, operating constraints, and service requirements.
For critical lanes, review backup carriers and discuss sustained changes before renewal. Contracts remain useful for predictability; the objective is to understand where their pricing and coverage assumptions may need attention.
For fleet operators: protect the capacity already available
Operators have a different set of decisions. Market rates affect revenue opportunities and replacement costs, but daily execution depends on the vehicles and people available for each run.
- Check vehicle readiness before assignment. Review inspection defects, repair status, and upcoming maintenance so the schedule reflects what can actually be deployed.
- Match driver availability to the plan. Review leave, callouts, required qualifications, and backup coverage before a gap becomes a missed departure.
- Track disruptions through resolution. Record what happened, who is responsible for follow-up, and whether the affected run has been covered.
- Separate market-driven costs from internal losses. Higher purchased-transportation rates and avoidable downtime are different problems. Tracking them separately helps teams choose the right response without treating maximum utilization as a reason to compromise maintenance or safe operating limits.
Act while there is still time to adjust
The spot-contract gap is useful because it can reveal changing conditions before an individual agreement is revisited. Its value depends on what transportation teams do next: buyers can review lane exposure and carrier coverage, while operators can address vehicle and driver readiness.
A contract records agreed terms. Reliable execution requires an up-to-date view of the capacity available to fulfill them.
LMDmax
How LMDmax helps protect usable capacity
Usable capacity depends on knowing which vehicles and drivers are ready for each run. LMDmax Fleet keeps inspections, defect records, work orders and preventive-maintenance scheduling together, and Intelligent Scheduler keeps driver availability, leave, callouts and backup coverage in one place. Managed support can handle scheduling follow-up and documentation at your direction, inside your systems. None of this guarantees that every vehicle will stay available.
